|
07-02-2017, 06:33 PM
|
#1
|
Member
Name: Bruce
Trailer: Burro
Alaska
Posts: 60
|
How to secure Burro hitch to ball?
I'm not comfortable hauling my Burro w/o some kind of pin or something to secure the hitch cap. I have no idea how to do it, as this style is new to me. Maybe you're not supposed to secure it? I'll replace it with a conventional hitch if necessary. Please and thanks...
|
|
|
07-02-2017, 06:41 PM
|
#2
|
Senior Member
Name: Robert
Trailer: 2015 Escape 19 "Past Tents" 2018 F150 Lariat 2.7L EB SuperCrew
Arkansas
Posts: 1,298
|
Looks like a common "yoke style" receiver hitch. There's no need to replace it if it latches well. The pin is just to keep the latch from being lifted. They've been doing it that way for a long time, regardless of the slight differences in receiver design.
Also, if it doesn't latch well, there are two fixes that don't require replacing the entire receiver:
1- adjust it. There's usually an adjustable bolt underneath to change the tension.
2- repair it. There are many 2" yoke type receiver repair kits available.
__________________
"You can't buy happiness, but you can buy an RV. And that is pretty close."
|
|
|
07-02-2017, 06:54 PM
|
#3
|
Member
Name: Bruce
Trailer: Burro
Alaska
Posts: 60
|
Thanks Robert,
Good info. I might tighten the tension a tad. I believe you're also saying there is no reason or way to pin the latch.
I can now rest assured!
|
|
|
07-02-2017, 11:15 PM
|
#4
|
Senior Member
Name: Robert
Trailer: 2015 Escape 19 "Past Tents" 2018 F150 Lariat 2.7L EB SuperCrew
Arkansas
Posts: 1,298
|
Quote:
Originally Posted by Biasdr
Thanks Robert,
Good info. I might tighten the tension a tad. I believe you're also saying there is no reason or way to pin the latch.
I can now rest assured!
|
A minor correction. It's not called a receiver, that's the part where the stinger attaches to the tow vehicle. Don't know why I called it that..lol. It's called a coupler. And, the more I look at the design (mine is a yoke style Atwood coupler), there is no bolt underneath to adjust it. The yoke style doesn't use one.
As long as the latch is secure and can't open on it's own, your coupler is probably fine. If you want to get down on the ground and inspect it, or use a small mirror, you will see how the little jaw operates when it's open or closed.
The one thing you have to make sure of is that the ball is properly seated in the coupler. With the yoke style coupler, that's easy - the latch will fully close.
__________________
"You can't buy happiness, but you can buy an RV. And that is pretty close."
|
|
|
07-02-2017, 11:25 PM
|
#5
|
Member
Name: Bruce
Trailer: Burro
Alaska
Posts: 60
|
Robert, thanks for the update. I do see the jaw now and can verify the coupler won't latch until the ball is proper seated. Once seated I can't physically pull it back. I'm confident using it now. Again, thanks for the information.
|
|
|
07-03-2017, 12:06 AM
|
#6
|
Senior Member
Name: Robert
Trailer: 2015 Escape 19 "Past Tents" 2018 F150 Lariat 2.7L EB SuperCrew
Arkansas
Posts: 1,298
|
Quote:
Originally Posted by Biasdr
Robert, thanks for the update. I do see the jaw now and can verify the coupler won't latch until the ball is proper seated. Once seated I can't physically pull it back. I'm confident using it now. Again, thanks for the information.
|
You're welcome. Happy camping.
__________________
"You can't buy happiness, but you can buy an RV. And that is pretty close."
|
|
|
07-03-2017, 07:06 AM
|
#7
|
Senior Member
Trailer: No Trailer Yet
Posts: 700
|
I think we have the same coupler type. This is an Atwood coupler.
Newer models of this coupler have a hole where you can insert a pin or lock, just like most regular couplers, to prevent the lever from lifting and releasing the ball.
Old models like ours don't have that.
When I bought my trailer, the previous owner showed me how he locked it. There is a hole on the side of the coupler, curb side, just behind the U-shaped part that slides forward and down to lock the ball. He inserted a lock pin in that hole, which prevents the U-shaped part (I don't know the name of that thing!) from sliding back.
I thought that was a bit of a redneck solution, but searching the web I found that this hole wasn't drilled by some previous owner, they were made like that. This hole is there from the factory, it's purpose is to lock the coupler, and it works just fine.
Here's a newer Atwood coupler, where you can insert a pin and lock it just like any coupler:
I couldn't find any pictures online for the old models, but here's mine. You can see the hole I'm talking about :
[/URL][/IMG]
You can see that when the coupler is unlocked, the hole is covered by the locking mechanism.
[/URL][/IMG]
When there is a pin or padlock in that hole, there is no way for the coupler to unlatch:
[/URL][/IMG]
|
|
|
07-03-2017, 09:18 AM
|
#9
|
Member
Name: Bruce
Trailer: Burro
Alaska
Posts: 60
|
Very cool! Already have one of those "U" pins and put it in the hole. Rev 'em up- I'm ready to go! Thanks!
Hey, just thought a long padlock might take care of hitch and chains... I'll check it after the rain stops.
|
|
|
07-03-2017, 09:23 AM
|
#10
|
Member
Name: Jim
Trailer: Burro
California
Posts: 36
|
Burro Hitch
As you, I was worried about my hitch when I first picked up my 83 burro, because I had never seen one like that before. I have learned to trust it. To secure the top latch I got a piece of metal (about 2-3X the thickness of a wire coat hanger) and bent it into a "C" so the top of the wire bends into the hole in the latch and the bottom bends under the hitch -- this keeps the latch from ever popping up (assuming it ever would) - and it's easy to assemble and disassemble.
|
|
|
07-03-2017, 10:42 AM
|
#11
|
Senior Member
Trailer: Scamp 19 ft 5th Wheel
Posts: 1,861
|
If you look at Carl's pictures of the older lock you will see LOCK factory stamped above the hole. In Va. you are required to have a external pin or locking device on your coupler. I was worried I was going to have to replace a coupler on an older Scamp but I found the lock hole on the side of the coupler.
Your state regulations may vary.
Eddie
|
|
|
07-03-2017, 11:18 AM
|
#12
|
Senior Member
Trailer: Scamp
Posts: 7,056
|
We travel a lot and stop for breakfast, lunch, and dinner while on the road. I have less concern about the latch coming open then I do about forgetting to latch or somebody playing silly games and unlatching while I'm parked. Therefore a padlock through any locking hole will 1) help to insure I've latched the coupler 2) at least slow down somebody that would want to play games 3) it makes it easy to check before leaving after any stop.
__________________
Byron & Anne enjoying the everyday Saturday thing.
|
|
|
07-03-2017, 11:32 AM
|
#13
|
Member
Name: Bruce
Trailer: Burro
Alaska
Posts: 60
|
Padlock it is. I tell ya, this forum is a gift. Anyone have ideas about my trailer plug? I'm on my 3rd day trying to figure it out. "Trailer/Truck" under Problem Solving sub forum. Again, many thanks, guys!!
|
|
|
07-03-2017, 02:04 PM
|
#14
|
Senior Member
Trailer: No Trailer Yet
Posts: 700
|
Quote:
Originally Posted by Eddie Longest
you will see LOCK factory stamped above the hole.
|
Wow I didn't even know that!
I figured may be you saw this before on someone else's coupler, not mine, as mine had been repainted so many times over the years that it must have 1/4 inch of paint on it! But no, to my surprise, the LOCK stamped on mine is clearly visible on my photo!
That's good!!
|
|
|
07-05-2017, 09:37 AM
|
#15
|
Senior Member
Name: Bill
Trailer: Burro 1983 13'
Wisconsin
Posts: 141
|
Thanks guys this was very helpful!
I will be using a lock from now on.
|
|
|
11-27-2019, 01:55 PM
|
#16
|
Senior Member
Name: Larry
Trailer: Burro
California
Posts: 128
|
Thanks for the info and photos.
I too wondered how to lock the hitch and was planning on all kinds of holes and locks.
The “lock” word was very hard to see on the curb side, but it is there!
Now I have a padlock thru it parked or towing.
Thanks to all of you.
LG- Burroman
|
|
|
10-06-2021, 09:59 PM
|
#17
|
Junior Member
Name: rudy
Trailer: Hunter Jr Compact
California
Posts: 7
|
Thank you!
I’ve had my 74 hunter for 2 years and was always worried about being able to lock it. Driving down the road or when leaving it parked at a hotel overnight. Your explanation of how to lock it has just resolved an issue I’ve had for so long. I’ve seen the hole there so many times, but never knew the solution was right in front of me. So glad these forums exists and everyone can help each other out with their knowledge and recommendations.
Quote:
Originally Posted by Carl V
I think we have the same coupler type. This is an Atwood coupler.
Newer models of this coupler have a hole where you can insert a pin or lock, just like most regular couplers, to prevent the lever from lifting and releasing the ball.
Old models like ours don't have that.
When I bought my trailer, the previous owner showed me how he locked it. There is a hole on the side of the coupler, curb side, just behind the U-shaped part that slides forward and down to lock the ball. He inserted a lock pin in that hole, which prevents the U-shaped part (I don't know the name of that thing!) from sliding back.
I thought that was a bit of a redneck solution, but searching the web I found that this hole wasn't drilled by some previous owner, they were made like that. This hole is there from the factory, it's purpose is to lock the coupler, and it works just fine.
Here's a newer Atwood coupler, where you can insert a pin and lock it just like any coupler:
I couldn't find any pictures online for the old models, but here's mine. You can see the hole I'm talking about :
[/URL][/IMG]
You can see that when the coupler is unlocked, the hole is covered by the locking mechanism.
[/URL][/IMG]
When there is a pin or padlock in that hole, there is no way for the coupler to unlatch:
[/URL][/IMG]
|
|
|
|
10-07-2021, 02:11 PM
|
#18
|
Senior Member
Trailer: 13 ft Scamp
Posts: 1,773
|
After I connect my trailer to the ball I “always” crank down the rolling / flat foot ( depending on my trailer)
If my tow vehicle raises a bit then I know it is secured
https://shop.harborfreight.com/media...9/69780_W3.jpg
|
|
|
10-07-2021, 04:01 PM
|
#19
|
Senior Member
Name: Pat
Trailer: 2006 Scamp 19 Deluxe
Enchanted Mountains of Western New York State on the Amish Trail in Cattaraugus County!
Posts: 621
|
Quote:
Originally Posted by Biasdr
Padlock it is. I tell ya, this forum is a gift. Anyone have ideas about my trailer plug? I'm on my 3rd day trying to figure it out. "Trailer/Truck" under Problem Solving sub forum. Again, many thanks, guys!!
|
Couldn't find your question about trailer plug under problem solving - ask again here or pm me.
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
» Upcoming Events |
No events scheduled in the next 465 days.
|
|