1970 Boler renovation

[Pgmopar]

So when asking questions it was requested​ that I post some progression pics. So here they are.

[Pgmopar]

This is the start point

[Pgmopar]

Originally Posted by Pgmopar

This is the start point

[Pgmopar]

Everything pulled out

[Pgmopar]

Originally Posted by Pgmopar

Everything pulled out

[Pgmopar]

Trailer and shell separated

[Pgmopar]

Originally Posted by Pgmopar

Trailer and shell separated

at least 3 or 4 repairs to hitch point so old hitch removed.

[Pgmopar]

Originally Posted by Pgmopar

at least 3 or 4 repairs to hitch point so old hitch removed. End boxed in waiting for new hitch.

Attachment 105200

[Pgmopar]

Originally Posted by Pgmopar

Attachment 105201

new hitch tacked on. Extended 18"

[Pgmopar]

Originally Posted by Pgmopar

Attachment 105202 new hitch tacked on. Extended 18"

new stronger support for door frame and step.

[Pgmopar]

Originally Posted by Pgmopar

Attachment 105203 new stronger support for door frame and step.

4" block installed to lift trailer. So more camp sites in northern British Columbia can be accessed.

[Pgmopar]

Originally Posted by Pgmopar

Attachment 105204 4" block installed to lift trailer. So more camp sites in northern British Columbia can be accessed.

Dual propane tanks and spare tire carrier spot installed. And battery box. The trailer was not 12v compatible. It will be now.

[Pgmopar]

Originally Posted by Pgmopar

Attachment 105205Dual propane tanks and spare tire carrier spot installed. And battery box. The trailer was not 12v compatible. It will be now.

first box of Amazon order. 7 wire harness and variable switches ,lights and system monitoring equipment.

[Johnny M]

before you go much further I would check the torsion axle...my 71 Ingersol Rub R Ride was wore out and I replaced it with a Dexter #9 for around $200 or so

[Pgmopar]

Originally Posted by Johnny M

before you go much further I would check the torsion axle...my 71 Ingersol Rub R Ride was wore out and I replaced it with a Dexter #9 for around $200 or so

Ty. Torsion appears still fine. At least it is light to Jack up if I need to grind off and replace....Lol

[Johnny M]

Originally Posted by Pgmopar

Ty. Torsion appears still fine. At least it is light to Jack up if I need to grind off and replace....Lol

Mine did too until I noticed my brand new tires had severe tread wear on the inside shoulder of both tires, up close you couldn't tell but when I looked at them from a distance in a large parking lot you could see the tires leaning in towards each other. If it is the original axle you will probably find a small plate on the axle tubing close to one side that reads "Ingersol Rub R Ride". Mine had paint on it but cleaned off you could see the embossing of the letters. If you find that I would highly recommend replacing it, but it is possible yours has been replaced since 1970 (but not likely).

[Pgmopar]

I hope it is ok. I am doing this rebuild for one camping trip per year. But I will definitely look for odd wear on the tires. Thanks for the heads up. I will also look for what that plate says. Didn't even think of looking at it. Good info.

[Pgmopar]

Shell sanded and area around old vent sanded down to cover up. All cracks sanded away to start repairs. Now to move outside degrease and wash. Then repairs start this week.

[Pgmopar]

Originally Posted by Pgmopar

Shell sanded and area around old vent sanded down to cover up. All cracks sanded away to start repairs. Now to move outside degrease and wash. Then repairs start this week.

[Pgmopar]

Washed the shell down from sanding. I missed a few spots.