|
07-28-2013, 05:30 PM
|
#1
|
Member
Name: JD
Trailer: Fiber Stream
Maryland
Posts: 35
|
Refurbing an '82 Fiber Stream
Accomplished a lot today with the help of two helpers.
Once we got it up in the air we used electric and air tools to wire brush and grind the entire frame and cross members. We then wiped it all down with mineral spirits before brushing on Rustoleum rust inhibitor. We also did the hitch and tank tray (taken down to bare metal as well), and all tank fittings and straps.
I've posted +30 pics on the site in the following link- look for the Fiber Stream link at the top of the main page on http://www.flyingtigertransport.com
We will post updates and the "After" shots soon.
Dave in Baltimore, MD, USA
82 Fiber Stream
|
|
|
07-31-2013, 11:52 AM
|
#2
|
Member
Name: JD
Trailer: Fiber Stream
Maryland
Posts: 35
|
Missing Reverse Wiring and Substitution Approach
We removed the old tail light units and I realized this unit never had reverse lights. Surprise! My new replacement Peterson's (Amazon) do, and they are required in Maryland as part of the inspection.
After realizing it would be tough to fish a new "yellow" lead through the frame I had a brainstorm Why not "steal" (re-purpose) the existing WHITE lead from the trailer/tow harness and use it as the in-frame lead for the reverse lights??
After installing a new Bargman splice box and trailer cable I disconnected the WHITE lead from the "common" terminal and tied it down under the YELLOW terminal (reverse from tug). Then, at the rear, I pulled a new WHITE and YELLOW lead from each tail light using the existing WHITE as a pull line. This gave me a replacement WHITE (common), and a YELLOW line for the reverse light. At the connection point in the hanging closet I cut the WHITE wire from the frame wiring and spliced it to the new YELLOW leads to the tail lights. I ran a new WHITE wire through the floor and bonded to the frame and tied all WHITE common wires at the rear to this new ground line. This saved me from having to run a yellow wire either in the frame or along another less secure route.
As a general rule in doing all refurbs I also removed all plastic connectors (many which have totally failed, one burned) and soldered and applied heat shrink tubing. We still have to do this throughout the unit, but look forward to getting rid of these really dangerous devices. I will post the picture of the COMMON white lead connector near the 12VDC converter that burned and failed - my first Fiber Stream electrical gremlin conquered!
Happy Camper
|
|
|
07-31-2013, 04:28 PM
|
#3
|
Moderator
Trailer: Fiber Stream 1978 / Honda Odyssey LX 2003
Posts: 8,222
|
Quote:
Originally Posted by JD1994
We removed the old tail light units and I realized this unit never had reverse lights.
After realizing it would be tough to fish a new "yellow" lead through the frame ...
|
My older Fiber Stream used a thin-wall plastic tube (drip irrigation line maybe?) as a conduit and strapped that to the frame. At 3 points spaced equally along the run from front to back they poked a hole through this tube to attach the white wire to the frame to make sure the frame is at "ground" potential. I would check yours to make sure you have not inadvertently grounded your reverse lights somewhere along the middle of the wire harness.
I had no problems fishing a new yellow wire for my reverse lights through my "conduit" .
__________________
Frederick - The Scaleman
|
|
|
08-01-2013, 06:52 PM
|
#4
|
Senior Member
Trailer: Boler (B1700RGH) 1979
Posts: 5,002
|
Quote:
Originally Posted by JD1994
We removed the old tail light units and I realized this unit never had reverse lights. Surprise! My new replacement Peterson's (Amazon) do, and they are required in Maryland as part of the inspection.
|
That's very unusual. Md. TRANSPORTATION Code Ann. § 22-221 (c) (2013) says:
Quote:
Any motor vehicle may be equipped with one or more backup lamps
|
Are you sure you need them?
__________________
1979 Boler B1700RGH, pulled by 2004 Toyota Sienna LE 2WD
Information is good. Lack of information is not so good, but misinformation is much worse. Check facts, and apply common sense liberally.
STATUS: No longer active in forum.
|
|
|
08-04-2013, 05:20 PM
|
#5
|
Member
Name: JD
Trailer: Fiber Stream
Maryland
Posts: 35
|
Quote:
Originally Posted by Brian B-P
That's very unusual. Md. TRANSPORTATION Code Ann. § 22-221 (c) (2013) says:
Are you sure you need them?
|
Thanks for the COMAR cite. Curious that it's the 2013 version, I will have to check further. All motorized and towed vehicles are required to have backup lights, and I don't think there is a weight limit exception (e.g. 1500 lbs). I will look into it, but I think they are handy to have especially since I want to setup the tow line to power the markers, tails and optionally, the reverse lamps for campsite lighting.
|
|
|
08-04-2013, 05:32 PM
|
#6
|
Member
Name: JD
Trailer: Fiber Stream
Maryland
Posts: 35
|
Updates
Just a few more items. I checked the white line in the frame bundle and it was free of any other grounds. Fred suggested that this might have ground take-offs as did his unit. I lucked out.
Using the old ceiling panels (after removing the fully intact and live insulation for re-use) I transferred the pattern onto the FRP stock. I slightly downsized the OA cuts to accomodate the side and center moldings. The #6 pan head screws are sized for plastic trim covers, and I will post the completed job soon. The FRP cut nicely with a sheet metal shear.
The 2nd pic of the interior is the location where I will run the 2 #14 wires for the Fantastic Fan. (more pics of that install later this week).
|
|
|
08-04-2013, 05:59 PM
|
#7
|
Senior Member
Trailer: Boler (B1700RGH) 1979
Posts: 5,002
|
Quote:
Originally Posted by JD1994
All motorized and towed vehicles are required to have backup lights, and I don't think there is a weight limit exception (e.g. 1500 lbs). I will look into it, but I think they are handy to have especially since I want to setup the tow line to power the markers, tails and optionally, the reverse lamps for campsite lighting.
|
I agree that reverse lights are good; the question is just if they are really required by law anywhere. The 4-pin wiring connection used almost universally for light general-purpose and RV trailers without electric brakes has no way to provide a reverse light circuit, and so almost every small utility trailer and rental cargo trailer would be illegal, if reverse lights were really required.
I have considered adding reversing lights - including docking lights on the sides - and just connecting them to the trailer's battery through a manual switch on the trailer. It would be rare to backup into a site without getting out to survey first, anyway, so manually hitting the switch would be no big deal.
__________________
1979 Boler B1700RGH, pulled by 2004 Toyota Sienna LE 2WD
Information is good. Lack of information is not so good, but misinformation is much worse. Check facts, and apply common sense liberally.
STATUS: No longer active in forum.
|
|
|
08-14-2013, 05:53 PM
|
#8
|
Member
Name: JD
Trailer: Fiber Stream
Maryland
Posts: 35
|
I replaced the old leaky vent with a fantastic fan on Sat. Every Philips head screw was rusted out and the unit was installed with hot glue. Yes, HOT GLUE. I hope no one else ever uses this method. Not only did it leak, but took over an hour to remove with a heat gun and putty knife.
I used a Dremal to cut slots in the screws then removed with a slotted driver: they all came out without breaking off. Not sure if the pics posted. If not I will repost from laptop.
|
|
|
08-14-2013, 06:23 PM
|
#9
|
Senior Member
Trailer: 1988 16 ft Scamp Deluxe
Posts: 25,697
|
I'm constantly amazed at some of the CRAPPY modifications some folks find have been done to these great trailers. HOT GLUE, oh my stars it wouldn't have surprised me if you said it was decades old silicone....
__________________
Donna D.
Ten Forward - 2014 Escape 5.0 TA
Double Yolk - 1988 16' Scamp Deluxe
|
|
|
08-15-2013, 10:56 PM
|
#10
|
Senior Member
Name: Jared
Trailer: 1984 19' scamp
Kansas
Posts: 1,610
|
Quote:
Originally Posted by Brian B-P
I agree that reverse lights are good; the question is just if they are really required by law anywhere. The 4-pin wiring connection used almost universally for light general-purpose and RV trailers without electric brakes has no way to provide a reverse light circuit, and so almost every small utility trailer and rental cargo trailer would be illegal, if reverse lights were really required.
I have considered adding reversing lights - including docking lights on the sides - and just connecting them to the trailer's battery through a manual switch on the trailer. It would be rare to backup into a site without getting out to survey first, anyway, so manually hitting the switch would be no big deal.
|
I put reverse lights on mine, they work great. I put them on an angle, I can't see through the camper, anyway.
|
|
|
08-20-2013, 11:58 AM
|
#11
|
Member
Name: JD
Trailer: Fiber Stream
Maryland
Posts: 35
|
Started topping the old floor with 3/4 ply and 1/2 angle. Used the angle to bridge the dropped area and bolted thru to raise the old ply. More pics when we finish. Makes a huge difference without having to replace whole floor.
|
|
|
08-20-2013, 12:03 PM
|
#12
|
Member
Name: JD
Trailer: Fiber Stream
Maryland
Posts: 35
|
A few more pics.
|
|
|
08-31-2013, 03:13 PM
|
#13
|
Member
Name: JD
Trailer: Fiber Stream
Maryland
Posts: 35
|
On the Road in Maryland with the Fiber Stream
First outing with the refurb'd unit. In central Maryland in KOA Antietam.
Plenty more cleaning and final outfitting and decorating going on. It's a wee bit small than the Airstream but cozy.
Was really surprised on how hard it was to fit the cushions to make up the bed. They are REALLY tight and REALLY firm. Actually, hard as a rock. Looking for a mattress topper before tonite!
|
|
|
09-10-2013, 10:51 AM
|
#14
|
Member
Name: JD
Trailer: Fiber Stream
Maryland
Posts: 35
|
Installed microwave in reefer cabinet. Very tight. Will install a fan to assure cooling when unit works.
Also changed out all cabinet latches.
|
|
|
09-10-2013, 11:07 AM
|
#15
|
Senior Member
Name: Carl
Trailer: 2013 Lil Snoozy #161 (SOLD)/2010 Tacoma
NE Oklahoma
Posts: 2,358
|
Enjoy all the projects and pictures.......
|
|
|
09-02-2014, 05:15 PM
|
#16
|
Member
Name: JD
Trailer: Fiber Stream
Maryland
Posts: 35
|
AC Installation and Testing- Works perfectly!
AC Installation and Testing- Works perfectly!
Just spent a season using this locally produced (Baltimore, MD USA) AC system.
Works great, no trailer modifications, and cheap compared to other approaches. This weekend (Labor Day 2014) was in the 90's where we were camping and it ran way too cold on the lowest setting.
Weighs about 60 lbs and will mount on the hitch with a optional rack. When hitch mounted you can feed cold air in the front window and exhaust from the side or install a thru-wall 6" fitting low near the floor. We're really pleased- and we use it hat home in a pinch when the AC failed in our family room!
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
Similar Threads
|
Thread |
Thread Starter |
Forum |
Replies |
Last Post |
MT- 82 Fiber Stream
|
kootenaigirl |
Referrals: Molded Fiberglass Trailers |
22 |
06-18-2012 09:51 AM |
Fiber Stream
|
Tom Bernardino |
Problem Solving | Owners Helping Owners |
8 |
10-12-2008 05:59 PM |
79' Fiber Stream
|
Robert N. |
General Chat |
2 |
09-11-2008 07:23 AM |
13' Fiber Stream
|
Roddy D |
Care and Feeding of Molded Fiberglass Trailers |
6 |
06-05-2008 10:56 PM |
79' Fiber Stream
|
Robert N. |
Modifications, Alterations and Updates |
0 |
01-01-1970 12:00 AM |
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
» Upcoming Events |
No events scheduled in the next 465 days.
|
|